ZeroWater Dissolved Solids Pitcher
1 package
On This Page
Directions
For Water Quality Meter: Remove cap, turn on, submerge in water, change filter when it reads 006 or higher. Troubleshooting Try These Tips: 1. Not getting a 000 reading? Ensure that the filter is threaded correctly and fully seated in the water reservoir. Watch for cross-threading and ensure that the rubber gasket is seated properly and has not gotten stuck in one of the threads. 2. Rinse and dry your pitcher/dispenser, TDS meter, and parts completely. Left over tap water, soap residue or a dirty TDS meter may give false meter readings. 3. Check the 0-ring on your filter. If there is no 0-ring present on your filter, unfiltered tap water will flow around the filter and into the dispenser. 4. Make sure you are pouring your filtered water into a clean glass. The indicator may pick up trace residue from previous use or soap. 5. Check for cracks in the reservoir or filter. If you have a crack, please contact customer service for additional instructions. Assembly Instructions: 1 Remove lid and water reservoir from top of the pitcher and remove filter from packaging. Unscrew the blue protective cap (if applicable). 2 Cleaning Instructions: Clean your device in warm water using mild soap then rinse and dry thoroughly. Additionally rinse the exterior of your filter with warm water for 30 seconds. 3 Twist: Filter into the bottom of reservoir (from below) and tighten filter to obtain a complete seal with the reservoir. Do not drop the filter in from above. Tighten until there is a complete seal between the filter, a-ring and reservoir. 4 Fill: Reservoir by pouring/filling with cold tap water (directly into the filter) and place lid on top. Allow all the water to pass through the filter before filling again. 5 Pour or Dispense: Using spigot (if applicable) to fill your cup or glass once the reservoir has emptied into the body.
Product Details
Zero dissolved solids for the purest tasting water. Manipuler robinet. The only filter certified to reduce Lead & Chromium: Lead - Zero water. Chromium - Zero water. Data reflected on this table was derived from the NSF International website. Rated service life is 20 gallons. It is recommended to change the filter with replacement element ZR-001/ZF-201 at this point. Service flow rate is 2.0 gallons per day. Operating temperature is 40-90 degrees F. This water treatment device is intended only for use with potable water. Do not use water that is microbiologically unsafe or of unknown quality without proper disinfection before or after the system. This system has been tested and certified by NSF International under NSF/ANSI standards 53 and 42 for the reduction of substances: Substance (NSF/ANSI Standard 53 - Health Effects): Chromium Hexavalent, pH 6.5: Overall Percent Reduction (99.6), Influent Challenge (Concentration (mg/L)): 0.3 +/-10%, Maximum Effluent Concentration (mg/L): 0.003, Maximum Permissible Effluent Concentration (mg/L): 0.050; Substance (NSF/ANSI Standard 53 - Health Effects): Chromium Hexavalent, PH 8.5: Overall Percent Reduction (99.6), Influent Challenge (Concentration (mg/L)): 0.3 +/-10%, Maximum Effluent Concentration (mg/L): 0.002, Maximum Permissible Effluent Concentration (mg/L): 0.050; Substance (NSF/ANSI Standard 53 - Health Effects): Lead, PH 6.5: Overall Percent Reduction (99.7), Influent Challenge (Concentration (mg/L)): 0.15 +/-10%, Maximum Effluent Concentration (mg/L): 0.005, Maximum Permissible Effluent Concentration (mg/L): 0.010; Substance (NSF/ANSI Standard 53 - Health Effects): Lead, PH 8.5: Overall Percent Reduction (95.9), Influent Challenge (Concentration (mg/L)): 0.15 +/-10%, Maximum Effluent Concentration (mg/L): 0.0075, Maximum Permissible Effluent Concentration (mg/L): 0.010; Substance (NSF/ANSI Standard 53 - Health Effects): Mercury, PH 6.5: Overall Percent Reduction (96.7), Influent Challenge (Concentration (mg/L)): 0.006 +/-10%, Maximum Effluent Concentration (mg/L): 0.0002, Maximum Permissible Effluent Concentration (mg/L): 0.002; Substance (NSF/ANSI Standard 53 - Health Effects): Mercury, PH 8.5: Overall Percent Reduction (96.0), Influent Challenge (Concentration (mg/L)): 0.006 +/-10%, Maximum Effluent Concentration (mg/L): 0.0004, Maximum Permissible Effluent Concentration (mg/L): 0.002; Substance (NSF/ANSI Standard 53 - Health Effects): PFOA/PFOS: Overall Percent Reduction (94.9), Influent Challenge (Concentration (mg/L)): 0.0015 mg/L +/-10%, Maximum Effluent Concentration (mg/L): 0.00007, Maximum Permissible Effluent Concentration (mg/L): 0.00007. NSF/ANSI Standard 42 - Aesthetic Effects: Chlorine: 97.5 (Percentage (mg/l)), 2.0 +/-10% (Concentration (mg/l)), 0.5 (Concentration (mg/l)), 50% of influent (Concentration maximum (mg/l)). TDS Water Quality Meter: The TDS meter supplied is intended to detect and measure TDS (total dissolved solids) in PPM. Test your water regularly. Water quality meter. Battery compartment. On/off. Hold button (optional). Maximum immersion level. TDS meters included with select ZeroWater pitchers/dispensers. ZeroWater Performance Data Sheet. For Models: ZD-018, ZP-006, ZP-010, ZD-010RP, ZD-023-1, ZD-012RP, ZP-007RP, ZBD-040, ZD-030RP, ZR-0810N, ZR-0810GN, ZD-20RPN, ZS-011RPN, ZBD-030 // Important Notice: Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs. It is recommended that before purchasing a water treatment unit you have your water supply tested to determine your actual water treatment needs. All contaminants reduced by this water treatment device are not necessarily in your water supply. While testing was performed under standard laboratory conditions, actual performance may vary. This system has been tested according to NSF/ANSI 42 and NSF/ANSI 53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in the relevant standard. NSF Independently Certified: System Tested and Certified by NSF International against NSF/ANSI Standard 42 for reduction of chlorine taste and odor and against NSF/ANSI Standard 53 for reduction of lead, chromium (Hexavalent). PFOA, PFOS and mercury. Replacement Battery Instructions: Meter includes (2) alkaline batteries. Do not mix old and new batteries. Do not mix alkaline, standard or rechargeable batteries. www.zerowater.com. For a complete list visit www.ZeroWater.com. For all other issues, please contact our customer service center at 1-800-503-2939 or email customerservice(at)zerowater.com.Nutrition Facts
Manufacturer
Zero Technologies, LLC
7 Neshaminy Interplex Suite 116 Trevose, PA 19053
UPC
00851510006019