Olympic Interior Oil Based Polyurethane, Satin Finish, 43806A
Interior Oil Based Polyurethane, Satin Finish, 43806A
Weight: 12 oz (340.2 grams)
Directions
Surface preparation: Surface should be clean and dry - free of dust, dirt, grease, wax and loose paint. New wood should be printed or undercoated before applying finish coat. Spraying tips: Cover floor and furniture where spray might settle. Shake can for at least one minute, listening for rattle of mixing ball. During application, shake intermittently for approximately 10 seconds at 1 to 2 minute intervals. Press valve all the way down. Do not extend finger beyond the value. Hold container about 6 to 8 inches from surface to be sprayed. Do not cover with continuous spray. Move back and forth, releasing sprayhead after each stroke. Overlap each stroke. Apply two thin coats rather than on heavy coat. If finish runs or sags, finish is being applied too heavily, or container is to close to surface. For best results, spray at room temperature 68 to 78 degrees F (20-26 degrees C). To prevent wrinkling or lifting, recoat within two hours or wait five days for thorough dry. Easy operation: Unique fanspray valve requires 50% less finger pressure than regular valves. Drying: Dries to touch in 15 to 30 minutes. Handle carefully for first few hours. Clean up: If spray button becomes clogged, pull off and clean with paint thinner. Do not stick pins or wire into can opening. Replace spray button firmly with valve opening pointing away from you. After use, invert can and spray for four seconds to clean valve. Avoid prolonged exposure to sunlight or heat sources that may cause bursting. Do not puncture, incinerate, burn or store above 120 degrees F. Do not discard empty can in home garbage compactor.
Product Details
Seals and protects from water, alcohol, household chemicals and stains. Durable extra hard abrasion resistant finish. Excellent for use on furniture, floors, doors, table tops, counter tops and other wood surfaces.
Ingredients
Acetone (30%), Xylene (19.5%), Urethane Polymer (14.5%), Propane/Butane (22%), Methyl Ethyl Ketone (10%), Ethylbenzene (3.5%), Amorphous Silica (0.5%).
Warnings
Danger! Extremely flammable. Contents under pressure. Vapor harmful. Harmful or fatal if swallowed. Irritant to eyes, skin and respirator tract. Do not spray near sparks, heat or open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated during use and until all vapors are gone. Do not smoke. Extinguish all flames, pilot lights and heaters. Turn off any other sources of ignition. Contents under pressure. This product contains a chemical (s) known to the State of California to cause cancer and birth defects or other reproductive harm. Vapor Harmful: Use with adequate ventilation. To avoid continuous breathing of vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA TC23C or equivalent) or leave the area. Avoid contact with skin and eyes. Wash thoroughly after handling. First Aid: In case of breathing difficulty, leave the area to obtain fresh air. If difficulty continues, get medical attention. If eye contact occurs, flush thoroughly with water for 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. Harmful or fatal if swallowed. If swallowed, do not induce vomiting. Get medical attention or contact a Poison Control Center immediately. Notice: Reports have associated repeated and prolonged occupational overexposures to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Keep out of reach of children. For emergency medical or spill control information, call (304) 843-1300.
Manufacturer
PPG Architectural Finishes, Inc.One PPG Place Pittsburgh, PA 15272
Copyright 1996
UPC
715195044547